[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: lb/hr calculation in ERROR (TunerCat vs. WinBin)




Yes, the 7730v3.ecu is in error which is what prompted my orig. posting
on how to fix the .ecu file format in general where the conversion eqn
involves the inverse. (1/x).  The 7730v3.ecu file is correct for the
stock 22lb inj size, but works in reverse as you move away from the stock
value.. (Same thing in the 7730v3.ecu for the Stoich value of 14.7 !)

So again, does anyone familiar with the .ecu format know of a way to
include a 1/x conversion, or is it a protocol error?  (for now I just 
have my .ecu file displaying the inverse of things when needed.. (sec/gm,
etc.)

mike


In message <NEBBIGHBJLLMAFPICMOHAEFMCCAA.trax@frederickmd.com>,trax writes:
>Guys,
>
>There HAS to be a discrepency between using WinBin with the 7730v3.ecu file
>and using TunerCats.
>
>I have a .bin that I created in TunerCats to have an injector flow rate of
>24.1lb/hr.  Using WinBin with the 7730v3.ecu file available at
>ftp://ftp.diy-efi.org/incoming/ shows an injector flow rate of 2.56
>grams/sec. which equates to 20.3lb/hr.
>
>So, I loaded the stock AUJP .bin into WinBin along with the 7730v3.ecu file.
>It reports 2.79 grams/sec which equates to 22.1lb/hr (which is correct).
>WinBin with the stock AUJP .bin and the 7730v3.ecu file has the correct
>values.  But, modified injector flow rates appear to be wrong.  This is an
>important issue which should be addressed ASAP for those of you guys who are
>using WinBin.  I am using TunerCat and everything appears to work great with
>TunerCat.
>
>FYI - I tried these calculations in the REVERSE order too.  I loaded a
>standard copy of the AUJP .bin file into WinBin with the 7730v3.ecu file.  I
>changed the stock injector flow rate from 2.79 grams/sec (01CC) to 3.03
>grams/sec (01F4) in order to produce a new injector flow rate of 24.1lb/hr.
>I saved the .bin and loaded it into TunerCat.  TunerCat now shows 20.3lb/hr
>for the injector flow rate.
>
>Somebody is obviously wrong here.  My bet is either WinBin or the .ecu file.
>
>Tim
>
>
>>-----Original Message-----
>>From: owner-gmecm@diy-efi.org [mailto:owner-gmecm@diy-efi.org]On Behalf
>>Of rr
>>Sent: Tuesday, June 13, 2000 8:11 PM
>>To: gmecm@diy-efi.org
>>Subject: Re: lb/hr calculation
>>
>>
>>
>>Wow, I'm having trouble following you guys. However, I think I see the
>>discrepancy. Tim, your equation below is a correct conversion from
>>gms/sec to lbs/hr.
>>
>>Looking at the anht hac, location 41c is in sec/gms, not gms/sec. This
>>appears to be the sticking point. That hac has 460 in that location
>>for 22# injectors.     ARG = ((SEC/GRAM * 256) * 5). The bigger
>>the injector, the smaller the number.
>>
>>BobR.
>>
>>
>>trax wrote:
>>
>>> Could someone here please post why my calculation is wrong (or if it is
>>> correct).  I just want to make sure that my new .bin will have the
>>> appropriate setting:
>>>
>>> 2.56g/s * 1lb/454g * 3600sec/Hr = 20.299559lb/hr
>>>
>>> Tim
>>>
>>> >The calc I posted matches the aujp bin, so I accept it to work.
>>> >It also matches the 38# setting
>>> >in the new "custom" chip I just wasted money on.
>>> >
>>> >I'm not a math wiz, so I can't twist it around like yours, but i'm
>>> >pretty sure yours is incorrect.
>>> >
>>> >Squash
>>> >p.s. I seem to recall that this calc is the same for the 7747, and
>>> >that is where I got it.  It
>>> >seems to jive in my head?
>>> >
>>> >--- trax <trax@frederickmd.com> wrote:
>>> >> Calculations:
>>> >>
>>> >> 2.56g/s * 1lb/454g * 3600sec/Hr = 20.299559
>>> >>
>>> >> Am I missing something?
>>> >>
>>> >> >1/(#hr/3600*453.59237)*1280  --  use this to get your value.  261
>>> >> >(dec) = 38 #/hr according to
>>> >> >this, and 462 = 22#, 423 = 24#
>>> >>
>>> >> Tim
>>> >>
>>> >-------------------------------------------------------------------
>>>
>>
>>-------------------------------------------------------------------
>>---------
>>To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
>>in the body of a message (not the subject) to majordomo@lists.diy-efi.org
>>
>>
>
>----------------------------------------------------------------------------
>To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
>in the body of a message (not the subject) to majordomo@lists.diy-efi.org
>
----------------------------------------------------------------------------
To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
in the body of a message (not the subject) to majordomo@lists.diy-efi.org