Promedit does the same.. Mike Rolica Plant A, Magnesium Products Division Strathroy (519)-245-4040 Ext. 265 -----Original Message----- From: Eric Aos [SMTP:EOA@spartek.com] Sent: Wednesday, June 14, 2000 10:51 AM To: 'gmecm@diy-efi.org' Subject: RE: lb/hr calculation in ERROR (TunerCat vs. WinBin) How does it work with Promedit? If someone will help walk thru this, I'll take a look at the code, and see what WinBin's doing. Eric > There HAS to be a discrepency between using WinBin with the > 7730v3.ecu file > and using TunerCats. > > I have a .bin that I created in TunerCats to have an injector > flow rate of > 24.1lb/hr. Using WinBin with the 7730v3.ecu file available at > ftp://ftp.diy-efi.org/incoming/ shows an injector flow rate of 2.56 > grams/sec. which equates to 20.3lb/hr. > > So, I loaded the stock AUJP .bin into WinBin along with the > 7730v3.ecu file. > It reports 2.79 grams/sec which equates to 22.1lb/hr (which > is correct). > WinBin with the stock AUJP .bin and the 7730v3.ecu file has > the correct > values. But, modified injector flow rates appear to be > wrong. This is an > important issue which should be addressed ASAP for those of > you guys who are > using WinBin. I am using TunerCat and everything appears to > work great with > TunerCat. > > FYI - I tried these calculations in the REVERSE order too. I loaded a > standard copy of the AUJP .bin file into WinBin with the > 7730v3.ecu file. I > changed the stock injector flow rate from 2.79 grams/sec > (01CC) to 3.03 > grams/sec (01F4) in order to produce a new injector flow rate > of 24.1lb/hr. > I saved the .bin and loaded it into TunerCat. TunerCat now > shows 20.3lb/hr > for the injector flow rate. > > Somebody is obviously wrong here. My bet is either WinBin or > the .ecu file. > > Tim > > > >-----Original Message----- > >From: owner-gmecm@diy-efi.org > [mailto:owner-gmecm@diy-efi.org]On Behalf > >Of rr > >Sent: Tuesday, June 13, 2000 8:11 PM > >To: gmecm@diy-efi.org > >Subject: Re: lb/hr calculation > > > > > > > >Wow, I'm having trouble following you guys. However, I think > I see the > >discrepancy. Tim, your equation below is a correct conversion from > >gms/sec to lbs/hr. > > > >Looking at the anht hac, location 41c is in sec/gms, not > gms/sec. This > >appears to be the sticking point. That hac has 460 in that location > >for 22# injectors. ARG = ((SEC/GRAM * 256) * 5). The bigger > >the injector, the smaller the number. > > > >BobR. > > > > > >trax wrote: > > > >> Could someone here please post why my calculation is wrong > (or if it is > >> correct). I just want to make sure that my new .bin will have the > >> appropriate setting: > >> > >> 2.56g/s * 1lb/454g * 3600sec/Hr = 20.299559lb/hr > >> > >> Tim > >> > >> >The calc I posted matches the aujp bin, so I accept it to work. > >> >It also matches the 38# setting > >> >in the new "custom" chip I just wasted money on. > >> > > >> >I'm not a math wiz, so I can't twist it around like yours, but i'm > >> >pretty sure yours is incorrect. > >> > > >> >Squash > >> >p.s. I seem to recall that this calc is the same for the 7747, and > >> >that is where I got it. It > >> >seems to jive in my head? > >> > > >> >--- trax <trax@frederickmd.com> wrote: > >> >> Calculations: > >> >> > >> >> 2.56g/s * 1lb/454g * 3600sec/Hr = 20.299559 > >> >> > >> >> Am I missing something? > >> >> > >> >> >1/(#hr/3600*453.59237)*1280 -- use this to get your > value. 261 > >> >> >(dec) = 38 #/hr according to > >> >> >this, and 462 = 22#, 423 = 24# > >> >> > >> >> Tim > >> >> > >> > >------------------------------------------------------------------- > >> > > > >------------------------------------------------------------------- > >--------- > >To unsubscribe from gmecm, send "unsubscribe gmecm" (without > the quotes) > >in the body of a message (not the subject) to > majordomo@lists.diy-efi.org > > > > > > -------------------------------------------------------------- > -------------- > To unsubscribe from gmecm, send "unsubscribe gmecm" (without > the quotes) > in the body of a message (not the subject) to > majordomo@lists.diy-efi.org > ---------------------------------------------------------------------------- To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes) in the body of a message (not the subject) to majordomo@lists.diy-efi.org
<<application/ms-tnef>>