[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: vr ecu mapedit
How about Promedit?.
Bruce
----- Original Message -----
From: "Daniel Collins" <bossute@hotmail.com>
To: <gmecm@diy-efi.org>
Sent: Monday, September 04, 2000 2:43 PM
Subject: Re: vr ecu mapedit
> Does anyone know where I can find Mapedit ,ive looked on the archives but
> must be blind or just plain stupid ??
> I am attempting to change the ve table and bpc in my ecu to correct for
> different intake manifold and larger engine displacment.The ecu I am
using
> is a 1227165 derivitive with a map sensor program $5D.
>
>
> >From: Stuart Bunning <stuart@kenelec.com.au>
> >To: "Daniel Collins" <bossute@hotmail.com>
> >Subject: Re: vr ecu
> >Date: Mon, 04 Sep 2000 10:39:38 +1000
> >
> >
> >if you goto http://www.diy-efi.org/ it should be in the incoming ftp
> >site.... for gmecm... or just diy-efi..
> >that's where i got it... if you can find it ask someone on the list...
> >I haven't been on the list for about 6 months.. haven't been into it for
a
> >long time...
> >
> >
> >
> >At 06:20 pm 02/09/2000 +0900, you wrote:
> >>Stuart I have not heard of mapedit where can I find it on the internet ?
> >>I've included the base holden bin file that I started with for my last
> >>conversion but i didn't get to keep a copy of the finished calibration
> >>after i had one of the local chip tuners write a eprom for it.I use
> >>scanpro to see what was happening on the dyno and then told them were i
> >>wanted timing and fuel changes and in this case a bpc change for the
> >>larger displacent.A very slow and expensive process!
> >>
> >>
> >>>From: Stuart Bunning <stuart@kenelec.com.au>
> >>>To: "Daniel Collins" <bossute@hotmail.com>
> >>>Subject: Re: vr ecu
> >>>Date: Thu, 31 Aug 2000 09:10:44 +1000
> >>>
> >>>I got Kalmaker...
> >>>
> >>>I know where the tables are in the Bin's so I can edit manually...
> >>>although
> >>>it's a slow process....
> >>>have you used mapedit... I use that and setup a ECU file.. I may have a
> >>>ecu
> >>>file for your ECU...
> >>>If you send me the BIN I can have a look for you...
> >>>
> >>>
> >>>
> >>>At 09:35 pm 30/08/2000 +0900, you wrote:
> >>>
> >>>>My vr is a manual so it uses the 16183082 ecu which is a derivitive of
> >>>>the
> >>>>1227808.have you had any luck getting into the ecu program to change
the
> >>>>calibration.
> >>>>
> >>>>I have just fitted on of these ecus to a 400 pontiac firebird using a
> >>>>custom throtle body/injector rails I made unfortunately i had to get a
> >>>>shop to change the BPW to scale up from a 308 to 400 cubes , runs and
> >>>>idles good but I would like to get the calibration spot on.Have seen
and
> >>>>used a program called kallmaker, but the cost is prohibitive , to
remap
> >>>>vn-vr ecus .Very good contol but i was hoping it may be possible in
hex
> >>>>if
> >>>>i can learn , or using a program like cattuner?
> >>>>
> >>>>If you would like some shots of the efi installation send a email.
> >>>>
> >>>>I also have some vn bin files and calibration dumps , from a friend
that
> >>>>used to work for holden ,that shows what the calibrated values are in
> >>>>the
> >>>>bin files if your interested
> >>>>
> >>>>
> >>>>>
> >>>>>sorry I can't help you there... only played with the ecm the PCM
> >>>>>incorporated the electronic auto.. and i know nothing about that...
> >>>>>
> >>>>>
> >>>>>At 06:27 pm 28/08/2000 +0900, you wrote:
> >>>>>
> >>>>>>Just a query as to whether you found an american eqivilent to the vr
> >>>>>>pcm
> >>>>>>as I am trying to reprogram my vrv8 commodore.
> >>>>>>I was hoping to use cattuner but dont know what definition file to
> >>>>>>order
> >>>>>>if any?
> >>>>>>any help much appreciated
> >>>>>>
> >>>>>>
> >>>>>>
> >>>>>>Daniel Collins
> >>>>>>BOSSUTE@hotmail.com
> >>>>
> >>>>
>
>>>>________________________________________________________________________
_
> >>>>Get Your Private, Free E-mail from MSN Hotmail at
> >>>>http://www.hotmail.com.
> >>>>
> >>>>Share information about yourself, create your own public profile at
> >>>>http://profiles.msn.com.
> >>>
> >>>Best regards
> >>>
> >>>Stuart Bunning
> >>>Sales Engineer
> >>>Kenelec Scientific Pty Ltd
> >>>
> >>>Phone: 1300 73 22 33
> >>>FAX: 1300 73 22 44
> >>>Email: stuart@kenelec.com.au
> >>>Web: http://www.kenelec.com.au/
> >>
>
>>_________________________________________________________________________
> >>Get Your Private, Free E-mail from MSN Hotmail at
http://www.hotmail.com.
> >>
> >>Share information about yourself, create your own public profile at
> >>http://profiles.msn.com.
> >>
> >>
> >
> >Best regards
> >
> >Stuart Bunning
> >Sales Engineer
> >Kenelec Scientific Pty Ltd
> >
> >Phone: 1300 73 22 33
> >FAX: 1300 73 22 44
> >Email: stuart@kenelec.com.au
> >Web: http://www.kenelec.com.au/
> >
>
> _________________________________________________________________________
> Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com.
>
> Share information about yourself, create your own public profile at
> http://profiles.msn.com.
>
> --------------------------------------------------------------------------
--
> To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
> in the body of a message (not the subject) to majordomo@lists.diy-efi.org
>
----------------------------------------------------------------------------
To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
in the body of a message (not the subject) to majordomo@lists.diy-efi.org