RE: 1227727 INJ.DRV.

[Don.F.Broadus@ucm.com]

Some of the stuff  I have read says that they put the large fuses in the
system to handle 'peak ' current loads.
The HEI is a good example , even though I've never seen more than about 2.5
amps at max RPM on the bench
it is factory fused for 10 amps. An analog or digital meter would not
respond fast enough to see the peak current.
A current shunt or clamp on current probe connected to a scope would capture
the peak current signature.
 
Don  

> -----Original Message-----
> From:	Bruce Plecan [SMTP:nacelp@bright.net]
> Sent:	Thursday, October 19, 2000 7:17 PM
> To:	gmecm@diy-efi.org
> Subject:	Re: 1227727 INJ.DRV.
> 
> They will work for a while with insane loads, and then start to get
> erratic
> at high rpm, then will just work cold, and then not at all.
> I'd venture a quess that they slightly over rate the fuses so they aren't
> current limiting the normal operation of the injectors
> Bruce
> 
> > but the driver itself will handle 20 amps?
> >
> > Swayze
> > mswayze@truswood.com
> > kswayze@bellsouth.net
> > <8-{b>
> > ----- Original Message -----
> > From: "Squash" <realsquash@yahoo.com>
> > To: <gmecm@diy-efi.org>
> > Sent: Thursday, October 19, 2000 4:21 PM
> > Subject: Re: 1227727 INJ.DRV.
> >
> >
> > > Maybe it's because there are only 6 injectors vs. 8?
> > >
> > > Squash
> > >
> > > --- Swayze <kswayze@bellsouth.net> wrote:
> > > > I was looking at 1227727vette.zip jpegs last night and comparing
> them
> to
> > the
> > > > 91 lumina manuals I have so that I could be sure I wired up a
> harness
> > > > correctly (trying to map it out), and noticed that the injectors on
> the
> > > > vette 727 have a 20 amp fuse. The v-6 ones I have been looking at
> show
> a
> > ten
> > > > amp fuse. only thing on the circuits are the injectors and the
> drivers
> > in
> > > > the ECM.
> > > > question: is there a difference in the drivers on the ECM's between
> the
> > > > various 727's? if so, whats in the vette '727?
> > > >
> > > > byE
> > > > Mike
> > > > Swayze
> > > > mswayze@truswood.com
> > > > kswayze@bellsouth.net
> > > > <8-{b>
> > > >
> > >
> >
> >
> --------------------------------------------------------------------------
> > --
> > > > To unsubscribe from gmecm, send "unsubscribe gmecm" (without the
> quotes)
> > > > in the body of a message (not the subject) to
> > majordomo@lists.diy-efi.org
> > > >
> > >
> > >
> > > __________________________________________________
> > > Do You Yahoo!?
> > > Yahoo! Messenger - Talk while you surf!  It's FREE.
> > > http://im.yahoo.com/
> >
> >
> --------------------------------------------------------------------------
> > --
> > > To unsubscribe from gmecm, send "unsubscribe gmecm" (without the
> quotes)
> > > in the body of a message (not the subject) to
> majordomo@lists.diy-efi.org
> > >
> > >
> >
> >
> --------------------------------------------------------------------------
> --
> > To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
> > in the body of a message (not the subject) to
> majordomo@lists.diy-efi.org
> >
> >
> 
> --------------------------------------------------------------------------
> --
> To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
> in the body of a message (not the subject) to majordomo@lists.diy-efi.org


*********************************************************************************
This E-mail and any of its attachments may contain Unicom proprietary
information, which is privileged, confidential, or subject to copyright 
belonging to the Unicom family of Companies.  This E-mail is intended
solely for the use of the individual or entity to which it is addressed.  If
you are not the intended recipient of this E-mail, you are hereby notified
that any dissemination, distribution, copying, or action taken in relation
to the contents of and attachments to this E-mail is strictly prohibited
and may be unlawful.  If you have received this E-mail in error, please
notify the sender immediately and permanently delete the original and
any copy of this E-mail and any printout.  Thank You.
*********************************************************************************
----------------------------------------------------------------------------
To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
in the body of a message (not the subject) to majordomo@lists.diy-efi.org