Re: Distributorless ignition (I'm new around here)

["Bruce Plecan" <nacelp@bright.net>]

Maybe?.
The Northstar diagrams I've seen show everything to be inside the PCM, no
external module.
Any one know for sure on the Olds?.
Bruce


----- Original Message -----
From: <ae2598@wayne.edu>
To: <gmecm@diy-efi.org>
Sent: Tuesday, November 28, 2000 3:55 PM
Subject: Re: Distributorless ignition (I'm new around here)


> Yeah, northstar or aurora motors surely must use DIS.  Maybe the earlier
> caddy stuff too, like the HT4100?
>
> On Tue, 28 Nov 2000, Drew Skinner wrote:
>
> > What about the caddys?
> >
> > >>> nacelp@bright.net 11/28 1:08 PM >>>
> >
> > The ZR1 vettes, are the only ones I know of
> > Bruce
> >
> >
> >
> >
> > > Do any of the Yank GM cars run a 8 Cyl DIS spark system that we could
> > adapt
> > > the ignition module off like the Buick V6
> > > -----Original Message-----
> > > From: Bruce Plecan <nacelp@bright.net>
> > > To: diy_efi@diy-efi.org <diy_efi@diy-efi.org>
> > > Date: Thursday, November 23, 2000 4:46 PM
> > > Subject: Re: Distributorless ignition (I'm new around here)
> > >
> > >
> > > >
> > > >Electromotive sells all the bits to do that, and even  a.
> > > >ZR-1 are a parts source but rare.
> > > >Alternatives use two electromotive sensors and tone rings, inside the
oem
> > > >dissy
> > > >Some reading at the 332 site.
> > > >MSD supposedly has a v-8 dissy for SEFI so it has a synch signal, if
I
> > > >recall right.
> > > >Bruce
> > > >
> > > >>      I am intrested in making a distributorless ignition for my
early
> > V8
> > > >> engine...My electronics training is limited to a junior college
> > > >"Introduction
> > > >> to electronics" course and a semester of "Electronic math".  I have
> > read
> > > >> Drury's DDIS article...but even that was a little much for me, as I
> > > didn't
> > > >> understand alot of the lingo.
> > > >>      My goal right now is to just build the initial infrastructure
> > needed
> > > >to
> > > >> fire the coils at idle with static advance. I've broken this down
into
> > > >> subgroups:
> > > >>
> > > >> 1. Power my coils, The coils are junkyard sourced from the late
80's GM
> > > >3.8
> > > >> liter 6cyl three coil packs.  I've been looking for a four coil
pack
> > from
> > > >an
> > > >> Aurora or something but they don't seem to have trickled down to
the
> > > "pick
> > > >a
> > > >> part" yet.
> > > >>
> > > >> 2. Trigger the ignition, I was thinking of four hall effect
transducers
> > > at
> > > >90
> > > >> degree intervals and a magnet epoxied into the crank pulley.
> > > >>
> > > >> 3. Control the coils, Find the correct transistor to work with the
hall
> > > >> effects in order to control current to the coils.
> > > >>
> > > >>      My current quandary is what type of hall effect sensor I
should
> > > >choose,
> > > >> www.digikey.com requests info. such as "output type" and
"package/case"
> > > >and I
> > > >> really don't know what my parameters should be.  Can anyone suggest
the
> > > >best
> > > >> transducer for my application?  Someday I will advance to digital
> > control
> > > >of
> > > >> the advance curve and maybe even fuel injection but right now I am
just
> > > >> trying to keep everything as simple and cheap as possible.  My
sincere
> > > >thanks
> > > >> to those who have read this far...any input is valued.
> > >
> >
>> -------------------------------------------------------------------------
> > > -
> > > >--
> > > >> To unsubscribe from diy_efi, send "unsubscribe diy_efi" (without
the
> > > >quotes)
> > > >> in the body of a message (not the subject) to
> > majordomo@lists.diy-efi.org
> > > >>
> > > >>
> > > >
> > >
> >
>---------------------------------------------------------------------------
> > > -
> > > >To unsubscribe from diy_efi, send "unsubscribe diy_efi" (without the
> > > quotes)
> > > >in the body of a message (not the subject) to
majordomo@lists.diy-efi.org
> > > >
> > > >
> > >
> >
> --------------------------------------------------------------------------
> > --
> > > To unsubscribe from gmecm, send "unsubscribe gmecm" (without the
quotes)
> > > in the body of a message (not the subject) to
majordomo@lists.diy-efi.org
> > >
> > >
> >
>
> --------------------------------------------------------------------------
--
> > To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
> > in the body of a message (not the subject) to
majordomo@lists.diy-efi.org
> >
> >
>
> --------------------------------------------------------------------------
--
> > To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
> > in the body of a message (not the subject) to
majordomo@lists.diy-efi.org
> >
> >
>
>
> --------------------------------------------------------------------------
--
> To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
> in the body of a message (not the subject) to majordomo@lists.diy-efi.org
>
>

----------------------------------------------------------------------------
To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
in the body of a message (not the subject) to majordomo@lists.diy-efi.org