RE: single vs double batch fire

[Mike Rolica <mrolica@meridian-mag.com>]

Look down further... in ide parameters, there is an cut in an cut out for
the 730.. I belive it starts at $3E9 and ends at $3EF  (fuel out
parameters.... There is no af otpition flag for this..)
On the 165, it looks a little different.. haven't played with this but looks
like it is in the area of$3AB-$3AD
Mike Rolica
Plant A,
Magnesium Products Division
Strathroy

(519)-245-4040  Ext. 244



	-----Original Message-----
	From:	romans@starstream.net [SMTP:romans@starstream.net]
	Sent:	Friday, August 11, 2000 12:58 AM
	To:	gmecm@diy-efi.org
	Subject:	Re: single vs double batch fire

	How do you know?  Just curious.  The option in the air fuel words
just says
	double or single mode.
	Mark
	----- Original Message -----
	From: "Mike Rolica" <mrolica@meridian-mag.com>
	To: <gmecm@diy-efi.org>
	Sent: Thursday, August 10, 2000 10:58 AM
	Subject: RE: single vs double batch fire


	> The bin I'm currently using uses single fire for low bpw..... when
bpw
	gets
	> so low it switches to single fire..
	> Gonna play with it when I throw the 30lb injectors.
	> Mike Rolica
	> Plant A,
	> Magnesium Products Division
	> Strathroy
	>
	> (519)-245-4040  Ext. 244
	>
	>
	>
	> -----Original Message-----
	> From: romans@starstream.net [SMTP:romans@starstream.net]
	> Sent: Thursday, August 10, 2000 12:57 PM
	> To: gmecm@diy-efi.org
	> Subject: Re: single vs double batch fire
	>
	> Looking some bins and the air fuel mode words, working on a
	> different
	> problem i have found  that (89 Code) only the 305 5 speed bin uses
	> the
	> single fire mode.  All other F&Y body bins that I have looked at
use
	> double
	> fire mode.
	> Mark
	> ----- Original Message -----
	> From: "NickG" <nikog@mediaone.net>
	> To: <gmecm@diy-efi.org>
	> Sent: Thursday, August 10, 2000 9:03 AM
	> Subject: single vs double batch fire
	>
	>
	> > ECM in question: '165 with type 32 Prom
	> >
	> > What is the difference between single fire and double fire on
the
	> injectors?
	> > I've noticed that the eprom has an injector size value for each
of
	> these
	> > instances. Should these values always be the same? At what point
	> does the
	> > ECM switch from one mode to the other?
	> >
	> > If it works like I imagine, I would like to set the low-speed
	> injector
	> > sizing to open the injectors for a smaller amount of time, and
the
	> > high-speed sizing to something that will open the injectors
	> longer. Will
	> > this work?
	> >
	> > Thanks,
	> > Nick
	> >
	> >
	> >
	>
--------------------------------------------------------------------------
	> --
	> > To unsubscribe from gmecm, send "unsubscribe gmecm" (without the
	> quotes)
	> > in the body of a message (not the subject) to
	> majordomo@lists.diy-efi.org
	> >
	> >
	>
	>
	>
--------------------------------------------------------------------------
	--
	> To unsubscribe from gmecm, send "unsubscribe gmecm" (without the
	> quotes)
	> in the body of a message (not the subject) to
	> majordomo@lists.diy-efi.org
	>
--------------------------------------------------------------------------
	--
	> To unsubscribe from gmecm, send "unsubscribe gmecm" (without the
quotes)
	> in the body of a message (not the subject) to
majordomo@lists.diy-efi.org
	>
	>

	
----------------------------------------------------------------------------
	To unsubscribe from gmecm, send "unsubscribe gmecm" (without the
quotes)
	in the body of a message (not the subject) to
majordomo@lists.diy-efi.org
----------------------------------------------------------------------------
To unsubscribe from gmecm, send "unsubscribe gmecm" (without the quotes)
in the body of a message (not the subject) to majordomo@lists.diy-efi.org